医生换纱布竟将婴儿小拇指剪掉，细数那些令人发指
百度 在主要领导的高度重视和以身示范下，辽源市各部门纷纷开展走访慰问活动。
For questions about the Creality Ender 3 family of 3D printers
824 questions
1
vote
0
answers
13
views
Z-axis not rising enough?
I have a problem with the Creality Ender 3 Pro (v1) with Mainsail.
When printing everything seems ok for 3-4 layers then the nozzle seems too low and starts ‘banging’ on the already made points.
Via ...
- 111
0
votes
0
answers
26
views
Upgrading Ender 3 Pro with 400XL Bed and BL Touch
I am looking for some guidance on how to properly collect and combine all the firmware updates for a CR BL Touch and 400x400 bed extension. The problem arose when I accidentally overwrote or removed a ...
0
votes
0
answers
29
views
Ender 3 V2 Neo Loses Homing
After successful Auto Homing, my Ender 3 V2 Neo loses homing and the print nozzle drops from whatever Z-axis position down to the bed. This happens after 2 minutes of inactivity.
The X, Y and Z values ...
- 101
0
votes
0
answers
67
views
Ender 3 V3 KE: System error, try restarting
I’m reaching out in hopes of getting some advice or insight regarding my Ender 3 V3 KE. I recently opened up the printer to install an LED mod and am now unable to use the printer. It says “System ...
- 1
0
votes
0
answers
56
views
How do I safely disassemble this creality hot end
I have a Creality hot end that is marked for disposal due to its age, wear, and general poor condition.
The hot end has been removed from the printer but cannot easily be disassembled due to ...
- 2,320
0
votes
0
answers
22
views
Why does my Ender 3 sometime print the same file at different locations and in different sizes?
I'm rebuilding an old Ender 3 from parts, and am trying to set it up.
I have downloaded a calibration model from Thingieverse and opened it up with the latest version of Cura on Ubuntu.
I slice the ...
- 2,320
0
votes
1
answer
41
views
What would be gained from removing the electrical components from the frame of an ender 3 and make them desk standing?
On the Ender 3 the electrical components are attached to the frame by default.
The mainboard is housed under the frame on the left hand side. The screen is attached to the front right hand runner, and ...
- 2,320
1
vote
1
answer
35
views
How do I identify the X-axis belt length for an Ender 3 built from an upgrade kit?
I'm refurbishing an Ender 3 that was built from a kit, and then upgraded several times, so that parts like the mainboard and extruder no longer match the model of the frame and can't be used to ...
- 2,320
0
votes
1
answer
43
views
Ender 3 Pro suddenly printing too high!
I've got an Ender 3 Pro that I've had for several years now, and I can't say I've ever seen this before.
After leaving it powered off for a few days and coming back to it, it now starts printing ...
0
votes
1
answer
78
views
ender 3 won't home or auto level, nozzle hits bed and keeps going down
I recently acquired a kit built Ender 3 as part of a bigger lot, it has an unknown history and has been modified several times by previous owners. I do not have access to this information.
The axis ...
- 2,320
0
votes
0
answers
37
views
Screen bricks almost everytime I turn it off and now the screen won't read any FAT32 formatted SD cards to flash
I thought I'd ask this here before I contact Creality and make use of my warranty.
I have had my V3SE for about 6-8 months, and it's been through its fair share of use (but not print farm levels); ...
- 1
0
votes
1
answer
49
views
Trouble printing TPU
I am a newbie here to 3D printing. I am using the Creality Ender 3 v3 Plus. Using the Creality print 6.1 slicer. I have had good success printing PLA. Trying to print TPU, but having a little trouble. ...
1
vote
1
answer
64
views
Stringing after filament change
In my previous questions (here and here) I was trying to achieve a filament change without M600 command. Finally made it getting a good second colour adhesion. Now ...
- 155
0
votes
0
answers
23
views
Ender 3 with BL Touch, 4.2.7 Board and Swiss Metal hot end. Z offset wont change
Ender 3 with 4.2.7 Board and BL Touch and Swiss Metal hot end. I cannot seem to adjust the Z Offset to get the nozle to print. I have followed the instructionss but whenever I change the setting - ...
0
votes
0
answers
40
views
Ender 3 not printing full bed
I'm trying to print on an Ender 3 a piece 21.1?cm wide, but it gets shrunk at around 20.8?cm; I'm using no brim or skirt, and I know the printer can print larger than that because in the G-code there ...
- 113